★ Independently researched & tier-ranked — no paid placements · Updated November 2026
Home › Bathroom & Plumbing › Why Is My Toilet Running? 5 Common Causes and Fixes
Bathroom & Plumbing

Why Is My Toilet Running? 5 Common Causes and Fixes

Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.

The short answer: A running toilet is almost always caused by a faulty flapper, a misadjusted fill valve, a tangled or too-short chain, an overflow tube issue, or a leak in the tank. You can fix most of these in under 30 minutes with basic tools and parts that cost less than $20.

1. The Flapper Is Worn or Misaligned

The flapper is the rubber valve at the bottom of the tank that lifts when you flush and then seals to hold water. Over time, it warps, cracks, or gets covered in mineral deposits, so it doesn’t create a watertight seal. Water then constantly leaks from the tank into the bowl, causing the fill valve to run intermittently.

How to test: Put a few drops of food coloring in the tank. Wait 15 minutes without flushing. If color appears in the bowl, the flapper is leaking.

Fix: Turn off the water supply, flush to empty the tank, and remove the old flapper. Take it to a hardware store to match the size and style, or buy a universal one (about $5 to $10). Attach the new flapper to the overflow tube with the included hinge, and make sure it sits perfectly centered over the flush valve. Clean the rim with a cloth to ensure a good seal.

2. The Fill Valve Is Set Too High

The fill valve (or ballcock) controls the water level in the tank. If it’s set too high, water reaches the top of the overflow tube and continuously drains down into the bowl. You’ll often hear a hissing or trickling sound.

How to check: Remove the tank lid and look at the water level. It should be about 1/2 to 1 inch below the top of the overflow tube. There’s usually a water level mark on the inside of the tank.

Fix: Most fill valves have an adjustment screw or a clip on the float. Turn the screw counterclockwise to lower the float, or squeeze the clip and slide the float down. Flush and recheck until the water stops at the correct level. If your fill valve has a float cup, you can also bend the rod (if metal) down slightly.

3. The Chain Is Too Long or Tangled

The chain connecting the flush handle to the flapper can get tangled, kinked, or have excess slack. If it’s too long, it can sit on the flapper and prevent it from sealing. If it’s too short, it might hold the flapper open slightly.

Fix: Inspect the chain. It should have about 1/4 to 1/2 inch of slack when the flapper is closed. Remove any kinks or tangles. If it’s too long, unhook it from the handle and reattach using a different link. If it’s too short, you may need a longer chain (some flappers come with a spare). Also, ensure the handle lever isn’t sticking.

4. The Overflow Tube Is Cracked or Clogged

The overflow tube is a vertical pipe in the center of the tank that prevents flooding. If it cracks, water can leak out and constantly run. Also, if mineral deposits or debris clog the tube, water can’t drain properly, but more commonly, a crack causes a constant drip.

How to check: Dry the overflow tube with a towel, then look closely for hairline cracks. You can also run your fingers around it to feel for moisture. If the tube is cracked, you’ll need to replace the entire fill valve assembly (about $15 to $25).

Fix: Turn off the water, flush, and disconnect the water supply line from the bottom of the fill valve. Loosen the locknut and remove the old assembly. Install the new one according to the manufacturer’s instructions, which usually involves adjusting the height and tightening the nut. It’s a straightforward 15-minute job.

5. A Leak at the Tank or Bowl Gasket

Less common but possible, a leak can occur at the tank-to-bowl gasket (the large rubber seal between the tank and the bowl) or at the tank bolts. This causes water to pool on the floor or run down the side of the toilet, and you might hear a faint running sound.

How to check: Place a dry paper towel under the tank and on the floor around the base. Flush and wait. If the paper towel gets wet, you have a leak. Also check for dampness around the tank bolts.

Fix: Tighten the tank bolts gently (don’t overtighten, which can crack the porcelain). If that doesn’t stop the leak, replace the tank-to-bowl gasket. Turn off the water, disconnect the supply, unbolt the tank, lift it off, and scrape off the old gasket. Install a new one, reseat the tank, and tighten the bolts evenly. This is a bit more involved but still DIY-friendly.

Frequently Asked Questions

Why does my toilet run intermittently every few minutes?
That’s typically a flapper leak. The tank loses water slowly, and when it drops below a certain level, the fill valve kicks in. Replace the flapper first, and that usually solves it.

Can a running toilet increase my water bill significantly?
Yes. A badly leaking flapper can waste up to 200 gallons a day, which can add $20 to $50 to your monthly bill depending on your rates. Fixing it pays for itself in a month.

Should I call a plumber for a running toilet?
Most fixes are simple and safe. Try the flapper, fill valve adjustment, and chain first. If you’re uncomfortable or the problem persists after trying these, a plumber can help, but you’ll likely spend $100 to $200 for a simple fix.

If you’re looking for ways to enjoy your bathroom more after fixing that toilet, check out our 2026 Best Bath Bombs: Top 10 Soaking Favorites for a relaxing soak.

How we rank

We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.

Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.

Research-based comparison
Manufacturer specs & owner feedback
One transparent S–C rubric
Independently researched, no paid placements

Keep readingContinue the research

Update log

  • - Editorial and on-page review.
  • - Guide first published.