Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.
The short answer: Your Kurgo Tru-Fit isn’t staying secure usually because the tether is too long, the latch is clipped to the wrong anchor, the harness isn’t snugly fitted, or the seat belt isn’t locked. Fixing these takes under five minutes and makes a huge difference.
The Kurgo Tru-Fit harness uses a tether that clips to the car’s seat belt latch or LATCH anchors. If the tether is too long, the seat moves. First, locate the tether clip and adjust its length: most models have a sliding adjuster on the strap. Pull the adjuster to shorten the tether so the harness is snug against the seat, but not so tight that it pulls the harness off the dog.
Also, verify where you’re clipping it. For a secure installation, always attach the tether to a solid anchor point, like the metal latch of the seat belt, not to the webbing itself. If you’re using LATCH anchors, make sure the clip is fully engaged and the tether is routed correctly. A common mistake is attaching to a seat belt that isn’t locked, which allows slack.
Some Kurgo models allow you to thread the seat belt through a loop on the harness. If you do this, you must lock the seat belt. Here’s how: pull the seat belt all the way out, then let it retract slowly. You should hear a clicking sound, which means the belt is locked. Then buckle it. If the belt isn’t locked, the harness slides freely, causing the seat to shift.
If you’re using the tether instead, you don’t need to lock the belt, but make sure the tether is clipped to the latch plate and the belt is buckled. In a crash, a locked belt prevents forward motion, but for everyday security, a locked belt also stops rocking.
An improperly fitted harness is the number one cause of a loose dog car seat. The Kurgo Tru-Fit has a chest strap and a belly strap. Both should be snug: you should be able to slide one finger between the harness and your dog’s skin. If you can fit more, it’s too loose.
Also, check the placement of the front chest piece. It should sit in the middle of the chest, not riding up toward the neck or sliding down to the belly. Adjust the straps so the harness doesn’t rotate. A rotating harness makes the tether pull unevenly, causing the seat to tilt.
If you’re using a Kurgo booster seat (not just a harness), the base might have a strap that goes through the seat belt. That strap can loosen over time. Tighten it by pulling the adjuster webbing and re-locking. Also, ensure the base is flat on the seat. If the car seat is angled, the base can’t grip properly.
Another tip: some cars have a seat that is slightly sloped. Use a non-slip mat or a folded towel under the booster to level it. This helps the harness stay in place.
If you’re using LATCH anchors, know that not all cars have them in the rear middle seat. Also, some LATCH anchors are hidden deep in the seat crevice. Use the clip and push it firmly until it clicks. Test for movement by pulling on the harness after installation. If it moves more than an inch, adjust.
If you have a car with side airbags, never place the harness or booster in the front seat. Always install in the back seat. And if your car has seat belt pretensioners, they might lock the belt automatically, which is fine, but the tether clip should still be snug.
If you’ve done all of the above and the seat still isn’t secure, it might be time to evaluate if the product matches your vehicle. Some cars have wide, flat seats that make it hard for a harness to be stable. In that case, you might need a different style of car seat, like a booster with a rigid base.
For a list of highly recommended dog car seats that have passed more rigorous real-world testing, check out our best dog car seats guide. Remember, safety is the priority: a loose seat is a hazard in an accident.
Getting the right size is the foundation of a secure fit. Kurgo Tru-Fit harnesses come in sizes from extra small to extra large, and each size covers a range of girth measurements. To measure your dog, use a soft tape measure around the widest part of the ribcage, just behind the front legs. This is the chest girth. Also measure the neck circumference at the base of the neck where the harness collar sits. Write both numbers down and compare them to the manufacturer’s sizing chart. If your dog falls between two sizes, choose the smaller size only if the larger size’s minimum girth is still larger than your dog’s measurement. Otherwise, size up. A harness that is too large cannot be adjusted small enough to stay secure, no matter how much you tighten the straps. Owners commonly report that a correctly sized harness needs only minor adjustments after the initial fit.
Even with the right size, certain installation errors can make the Kurgo Tru-Fit feel insecure. Here are the most frequent ones reported by owners.
Twisted straps: If the webbing is twisted anywhere, the load is not distributed evenly. A twisted strap can also cause discomfort and make the harness shift. Always run your hand along each strap to ensure it lies flat against your dog.
Over-tightening the chest strap: While a snug fit is important, over-tightening the chest strap can cause the harness to ride up toward the neck. This changes the pull angle of the tether and can make the seat tilt. Aim for two fingers of space at the chest, not one.
Clipping the tether to a non-structural point: The tether must attach to a metal anchor, such as the seat belt latch plate or a designated LATCH anchor. Clipping it to the seat belt webbing itself, or to a plastic loop, will not hold in a sudden stop.
Ignoring the belly strap: The belly strap keeps the harness from rotating. If it is too loose, the harness can twist around your dog’s body during movement. Adjust it so it is snug but allows normal breathing.
Using a seat belt extender: Some owners use a seat belt extender to make buckling easier. However, extenders can introduce slack and are not recommended for use with a dog harness unless specifically approved by the manufacturer.
Over months of use, webbing can stretch, buckles can accumulate dirt, and adjusters can slip. Regular maintenance keeps the harness performing as intended.
Inspect the webbing: Check for fraying, cuts, or thinning. Even a small nick can weaken the strap. If you see damage, replace the harness.
Clean the buckles: Dirt and hair can prevent the clip from fully engaging. Use a damp cloth to wipe the clip and the adjuster. Do not use lubricants, as they can attract more debris.
Check the adjusters: Sliding adjusters can loosen over time. After each use, tug on the strap to ensure the adjuster is holding. If it slips, the harness may need to be replaced.
Hand wash only: As mentioned in the FAQ, hand wash with mild soap and air dry. Machine washing can stretch the webbing and damage the buckles.
Store properly: When not in use, hang the harness or store it flat. Do not leave it crumpled in a hot car, as heat can degrade the webbing over time.
Yes, the harness can be used alone with the seat belt tether. It’s designed to work either way, but the booster adds height and comfort. Without a booster, make sure the tether is short enough to limit movement.
Usually not. Check the sizing: measure your dog’s chest and neck. The harness should be tight but not restrictive. If your dog can back out, the belly strap is too loose. Adjust it to be snugger.
Hand wash with mild soap and air dry. Avoid machine washing, which can stretch or weaken the straps. Do not bleach. Regular cleaning helps maintain the integrity of the webbing.
By following these steps, you’ll likely solve the security issue. If not, contact Kurgo customer service for a replacement. Safe travels!
We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.
Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.