Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.
The short answer: Installing a smart toilet is doable for most DIYers, but it’s not a simple swap. You’ll need basic plumbing skills, the right tools, and about 2-4 hours. The key steps are: turn off water, remove old toilet, prepare flange, place new unit, connect water supply (and power if needed), and test for leaks. For many smart toilets, you’ll also need a nearby electrical outlet. If you’re not comfortable with plumbing or electrical work, call a pro. Otherwise, follow this guide carefully and you’ll be enjoying your smart toilet in no time.
Before you even think about wrenching off your old toilet, make sure you have everything ready. Smart toilets are heavier and more delicate than standard ones, so preparation is key.
Tools and materials:
Check your space:
Let’s get to work. First, turn off the water supply at the shut-off valve (usually located behind the toilet). Flush the toilet to drain the tank and bowl, then use a sponge or towel to remove remaining water. Disconnect the water supply line from the fill valve using a wrench.
Remove the caps on the floor bolts (if any) and unscrew the nuts. If your toilet is caulked around the base, cut the caulk with a utility knife. Gently rock the toilet from side to side to break the seal, then lift it straight up. It’s heavy, so get help if needed. Place it on a tarp or old towels. After it’s out, stuff a rag into the drain opening to prevent sewer gases from escaping.
Scrape off the old wax ring from the flange and the floor. Inspect the flange: it should be in good condition, not cracked, and securely attached to the floor. If the flange is broken or corroded, you may need to replace it. Also check the height: the flange should be about 1/4 inch above the finished floor. If it’s lower, you may need a flange extender.
Clean the area thoroughly, and dry it. Place the new wax ring on the flange. For smart toilets, many come with a foam seal or gasket that fits over the outlet. Follow the manufacturer’s instructions: some require a wax ring, others use a rubber gasket.
Now bring in the smart toilet. These units are heavy (often 80+ pounds), so get a friend to help. Lift the toilet and position it over the flange, making sure the horn on the bottom of the toilet aligns with the center of the flange. Lower it straight down, and press firmly to compress the wax ring. Do not rock or twist, as that can break the seal. Use a level to check both front-to-back and side-to-side. If it’s not level, use shims under the edges.
Once level, install the floor bolts and nuts, but don’t overtighten. You want to snug them down evenly until the toilet is stable and doesn’t move. Overtightening can crack the porcelain.
Now for the fun part. Smart toilets often have a separate supply line for the bidet function. Check the manufacturer’s instructions: some have a single water inlet, others have two. Attach the water supply line from the shut-off valve to the toilet’s inlet, using Teflon tape on the threads to prevent leaks. Tighten snugly.
If your smart toilet is electric (most with heated seats, warm water, and air dryers are), plug it into the outlet. Make sure the outlet is GFCI protected for safety. If not, consider having an electrician install one.
Turn on the water supply valve slowly, and check for leaks at the connection points and around the base. Flush the toilet a few times, and test all the smart features: bidet spray, seat heater, dryer, etc. If any leaks occur, tighten connections or reseat the toilet if necessary.
Once everything works, apply a bead of silicone caulk around the base of the toilet, leaving a small gap at the back to allow for any future leaks to be visible. Smooth it with your finger. Let it dry for 24 hours before using the shower or cleaning the floor.
Finally, set the seat and controls to your preferences. Some smart toilets come with a remote that needs to be paired. Follow the manual.
Yes, if you have basic DIY skills. The process is similar to a standard toilet, but you’ll also need to handle the electrical connection. If you’re not comfortable with plumbing or electrical work, or if your bathroom lacks an outlet near the toilet, it’s best to hire a professional.
Not necessarily, but the flange must be in good condition and at the correct height. Many smart toilets use a standard 12-inch rough-in, but check the specifications. Some come with a special seal that doesn’t require a wax ring, but you still need a secure flange.
For a DIYer, expect 2 to 4 hours, including prep and cleanup. If you need to run a new electrical outlet or replace the flange, it can take longer.
If you’re still in the shopping phase, be sure to check our guide to the best smart toilets to find one that fits your needs and budget.
We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.
Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.