★ Independently researched & tier-ranked — no paid placements · Updated November 2026
Home › Bathroom & Plumbing › How to Install a Tub Drain: Step-by-Step Guide
Bathroom & Plumbing

How to Install a Tub Drain: Step-by-Step Guide

Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.

The short answer: To install a tub drain, you need to remove the old drain (using a drain removal tool), clean the area, apply plumber’s putty or silicone sealant, insert the new drain, and tighten it securely. Then test for leaks. But the process varies based on your drain type, so read on for a detailed step-by-step guide that covers both pop-up and toe-touch drains.

Tools and Materials You’ll Need

Before you start, gather these essential tools and materials:

  • New tub drain kit (includes drain body, stopper, and overflow plate)
  • Drain removal tool (or a pair of pliers, a screwdriver, and a hammer)
  • Plumber’s putty or silicone sealant (check your drain manufacturer’s recommendation)
  • Pipe wrench or adjustable wrench
  • Screwdriver (flathead and Phillips)
  • Plumber’s tape (Teflon tape)
  • Rag or sponge
  • Bucket (to catch water)

If you’re replacing an old drain, you’ll also need a drain extractor (often a ‘drain key’ or a ‘drain puller’), which is available at hardware stores. This tool is specifically designed to remove stubborn drains without damaging the tub.

Step 1: Remove the Old Drain

First, close the drain stopper if it’s a pop-up type. If it’s a lift-and-turn or push-and-seal, you’ll need to remove the stopper first. For pop-up drains, you can often unscrew the stopper counterclockwise. For others, look for a small set screw on the side of the drain body that holds the stopper in place; remove it and pull out the stopper.

Next, insert the drain removal tool into the crossbars of the old drain. Use a wrench to turn it counterclockwise. If the drain is stuck, apply penetrating oil and let it sit for 15 minutes. Be careful not to slip and scratch the tub. Once it’s loose, unscrew it by hand and pull it out.

Step 2: Clean the Drain Area

With the old drain removed, you’ll see a gap between the tub and the drain pipe. Use a rag or sponge to clean out any old putty, debris, or hair. Make sure the area is dry before proceeding. If there is any old sealant residue, scrape it off carefully with a putty knife.

This is also a great time to inspect the condition of the drain pipe. If it’s corroded or damaged, you might need to replace it, but for most installations, it’s fine.

Step 3: Apply Plumber’s Putty

Roll a snake-like length of plumber’s putty in your hands to soften it. Then, wrap it around the underside of the drain flange (the lip that sits on the tub surface). You want a continuous bead that’s about 1/8 inch thick. This putty creates a watertight seal between the drain and the tub.

If your drain kit recommends silicone sealant instead, use that. Some new drains come with a rubber gasket, so you may not need putty. Always follow the manufacturer’s instructions for your specific drain.

Step 4: Install the New Drain

Carefully insert the new drain into the hole. Press down firmly to ensure the putty spreads evenly. Under the tub, you’ll have a rubber gasket and a metal washer that go over the threads. Slide them on, then screw on the locknut. Use a pipe wrench to tighten the locknut from below. You want it snug, but avoid overtightening, which can crack the tub.

After tightening, wipe away any excess putty that squeezes out from around the drain. Let it set for a few minutes.

Step 5: Reattach the Stopper and Overflow Plate

Now, reattach the stopper mechanism. For pop-up drains, you’ll need to connect the linkage rod to the overflow plate. Insert the clevis strap through the overflow hole and connect it to the rocker arm. Then, adjust the height so the stopper seals properly. For toe-touch or push-button drains, simply press the stopper into place.

Secure the overflow plate with screws. Make sure it’s aligned properly and snug. Test the stopper by pulling up and pushing down to ensure smooth operation.

Step 6: Test for Leaks

Run water into the tub and let it drain. Check under the tub for any leaks. Also, check around the overflow plate. If you see any leaks, tighten the connections or reapply sealant. It’s normal for a small amount of water to sit around the drain after testing; just wipe it dry and check again after a few minutes.

If everything looks good, you’re done! If you need to upgrade your drain or want to explore different styles, check out our best tub drain guide for top picks.

Frequently Asked Questions

Q: Do I need to use plumber’s putty or silicone?

A: It depends on your drain type. Many drains come with a rubber gasket that creates a seal, so putty is not needed. If not, plumber’s putty is great for metal drains, but silicone is better for plastic to prevent cracking. Always check the manufacturer’s instructions.

Q: What if my old drain is stuck?

A: Use a drain removal tool with a wrench. If it’s still stuck, apply heat from a hairdryer to soften any old putty, or use a penetrating oil like WD-40. Be patient and avoid excessive force to prevent damaging the tub.

Q: Can I install a tub drain without removing the old one?

A: No, you must remove the old drain to replace it. Trying to install a new drain over the old one will cause leaks and improper fit.

If you’re unsure about the process, consider hiring a professional. But with these steps, most DIYers can handle it. For more detailed product recommendations, see our tub drain buying guide.

How we rank

We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.

Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.

Research-based comparison
Manufacturer specs & owner feedback
One transparent S–C rubric
Independently researched, no paid placements

Keep readingContinue the research

Update log

  • - Editorial and on-page review.
  • - Guide first published.