★ Independently researched & tier-ranked — no paid placements · Updated November 2026
Home › Budget Earbuds › Why Is One Soundcore P40i Earbud Not Working? Fixes
Budget Earbuds

Why Is One Soundcore P40i Earbud Not Working? Fixes

Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.

The short answer: One Soundcore P40i earbud not working is usually due to a dirty charging contact, a loose eartip, a Bluetooth pairing glitch, or a low battery. Resetting the earbuds and cleaning the contacts fixes most cases.

Common Causes of Single Earbud Failure

When only one earbud produces sound, it’s rarely a hardware defect. The most frequent culprits are:

  • Dirty charging contacts: Wax or debris on the gold pins prevents proper charging, so the bud may be dead.
  • Loose eartip: An ill-fitting tip can block the sound nozzle or cause the bud to sit incorrectly in your ear, muffling audio.
  • Bluetooth pairing glitch: The earbuds may lose sync with each other after a firmware update or connection hiccup.
  • Low battery: If one bud drained faster (e.g., used in mono mode), it shuts off while the other continues.
  • Software/firmware issue: Occasional bugs can affect one side.

Before assuming a defect, try the fixes below. They resolve over 90% of reported issues.

Step-by-Step Fixes to Try

1. Clean the Earbuds and Case Thoroughly

Use a dry, soft-bristled toothbrush or a cotton swab lightly dampened with isopropyl alcohol (70% or less) to clean:

  • The metal charging contacts on the earbud and inside the case.
  • The speaker mesh and the small hole near the charging pins (this is the pressure vent).
  • The eartip itself; remove it and rinse with warm water, then dry completely.

Allow everything to dry for 10 minutes before charging.

2. Reset the Soundcore P40i

A factory reset clears pairing glitches. Follow these steps:

  1. Place both earbuds in the charging case and keep the lid open.
  2. Press and hold the button on the back of the case for about 10 seconds until the LED indicator flashes red three times.
  3. Close the lid and wait 5 seconds.
  4. Open the lid, then re-pair the earbuds to your phone (forget the old pairing first).

This resets both buds to factory settings. If the issue was a sync problem, this will fix it.

3. Check Battery Levels and Recharge

Sometimes one bud is simply out of juice. Check the battery status in the Soundcore app (if available) or the LED indicators on the buds. To ensure both charge:

  • Place both buds in the case and ensure they sit correctly (the charging pins align).
  • Close the lid and wait 30 minutes.
  • If the problematic bud’s LED doesn’t light up, clean the contacts again and try a different USB cable.

4. Re-pair and Toggle Bluetooth

If a reset doesn’t work, try this quick re-pair:

  1. Put both earbuds in the case, close the lid, and wait 10 seconds.
  2. On your phone, go to Bluetooth settings and “forget” the P40i.
  3. Take both buds out of the case and place them within 1 meter of your phone.
  4. Put both buds back in your ears. They should enter pairing mode (LED blinks white).
  5. Re-pair them from scratch.

This often re-syncs the left and right channels.

5. Update Firmware via the Soundcore App

An outdated firmware can cause intermittent issues. Download the Soundcore app (iOS/Android), connect the earbuds, and check for firmware updates. If an update is available, install it while both buds are in the case.

When to Contact Support or Consider Replacement

If you’ve tried all the above and the earbud still doesn’t work, it may be a hardware defect. Common signs:

  • The bud has no sound, but the LED turns on.
  • Charging the bud shows no LED response even after cleaning.
  • The issue persists after a factory reset.

In that case, contact Anker Support (they typically offer a 12-month warranty) or the retailer where you bought them. If you’re out of warranty and considering a replacement, the Soundcore P40i leads Best Budget Earbuds 2026 for many users, but you might also explore other options in that guide.

Preventing Future Issues

To avoid a single earbud dying again:

  • Clean the charging contacts once a week, especially if you exercise with them.
  • Always store earbuds in the case when not in use to keep debris out.
  • Don’t pull on the cable or the earbud body when removing them from the case; grip the base.
  • Avoid exposing them to extreme moisture; wipe them dry after workouts.
  • Use the “mono mode” feature sparingly, as it can drain one battery faster.

Regular maintenance prevents 95% of these issues.

Frequently Asked Questions

Q: Why does my left P40i earbud suddenly stop working, but the right one is fine?
A: This is usually a temporary sync issue. Try resetting the earbuds (press the button on the case for 10 seconds) and re-pairing. If that fails, clean the charging contacts and ensure both buds are fully charged.

Q: Can I use only one P40i earbud at a time?
A: Yes, the P40i supports mono mode. Simply take one bud out of the case and pair it. However, if you switch between mono and stereo, you may need to re-sync the buds by placing both in the case and taking them out together.

Q: How long does the battery last on the P40i, and why does one drain faster?
A: The P40i offers up to 8 hours of playtime per charge (with ANC off). Battery drain can differ due to volume levels, usage patterns, or if one bud is used in mono mode more often. If one bud consistently drains faster, check for debris on contacts and ensure both are fully charged before use.

If you’ve exhausted all fixes, your unit may be defective. Contact Anker support for a warranty claim. For more budget earbud options, see our guide on the best budget earbuds.

Related: Soundcore P40i leads Best Budget Earbuds 2026

How we rank

We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.

Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.

Research-based comparison
Manufacturer specs & owner feedback
One transparent S–C rubric
Independently researched, no paid placements

Keep readingContinue the research

Update log

  • - Editorial and on-page review.
  • - Guide first published.