Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.
The short answer: Setting up the Dolphin Nautilus CC Plus involves unboxing, connecting the cable to the power supply, positioning the unit in the pool, and plugging it in to start a cleaning cycle. The entire process takes about 10 minutes and requires no tools.
When you first receive your Dolphin Nautilus CC Plus, carefully open the box and remove all components. You should have the robotic cleaner itself, a floating cable (usually 50 feet long), a power supply unit (transformer), and an owner’s manual. Check that nothing is damaged during shipping. The cleaner looks like a small rectangular robot with brushes on the bottom and a filter compartment on top. The power supply is a compact box with a cord that plugs into a standard wall outlet.
Before you start, read the manual quickly to familiarize yourself with the parts. It’s also a good idea to check the filter bag or cartridge; the Nautilus CC Plus uses a fine filter that captures small particles. Ensure it is properly seated in the cleaner, as a loose filter can cause poor performance.
First, place the power supply unit near a grounded wall outlet, but keep it at least 10 feet away from the pool edge to avoid any splashing. Next, take the floating cable and plug it into the power supply. The connector is keyed, so it only fits one way. Push it in until it clicks securely. Then, connect the other end of the cable to the robot itself. This is usually a twist-lock connector on the top of the robot. Align the arrows and twist clockwise until it locks.
Make sure the cable is free of kinks and lies flat on the ground from the power supply to the pool. The floating cable is designed to float on the water surface, so do not coil it tightly while storing, as that can cause tangles.
Now, carry the robot by its handle and gently lower it into the pool water. The robot should be fully submerged. Do not drop it from a height, as that could damage the internal components. Submerge it at an angle to allow air to escape. Once it’s in the water, let it sink to the floor. The robot will automatically orient itself with the brushes down.
If your pool has a sloped bottom, place the robot in the shallow end first. Also, ensure that the power supply is plugged into the wall outlet. The robot will not start until it’s plugged in and the power is turned on.
After plugging the power supply into the outlet, the robot should power on automatically. Most models have a simple on/off switch on the power supply, or they start immediately when connected. The Nautilus CC Plus has a default cleaning cycle of 2 hours, which is usually sufficient for most pools. Some models have a quick clean mode for a 1 hour cycle, and a eco mode for longer, energy efficient cleaning. Refer to your manual to see which modes your unit supports.
To change modes, press the mode button on the power supply or on the robot itself (depending on the model). Note that the robot will climb walls and clean the waterline, so ensure the water level is at least halfway up the skimmer opening. If the water level is too low, the robot may not reach the waterline.
When the cycle completes, the robot will stop and float to the surface. To remove it, pull it out by the handle, but be careful not to lift it by the cable. Place it on the pool deck and let it drain. Then, open the top lid to access the filter. Rinse the filter with a garden hose to remove debris. For a deep clean, you can use a mild detergent and a soft brush, but avoid harsh chemicals. Let the filter air dry completely before storing.
Also, check the brushes for any hair or debris entanglement. If the brushes are worn, consider replacing them. Keep the robot and power supply in a shaded, dry area when not in use, away from direct sunlight.
If the robot doesn’t move after plugging in, check that the power supply is working (indicator light on). If the light is off, try a different outlet. Also, ensure the cable connections are secure. If the robot moves but doesn’t climb walls, check the water chemistry: high chlorine or low pH can affect performance. Also, make sure the filter is clean, as a clogged filter reduces suction.
If the robot keeps stopping, it might be stuck on a drain or a ladder. Remove any obstacles. If the robot stays at the bottom and doesn’t move, try resetting it by unplugging for 30 seconds and plugging back in. For persistent issues, consult the manual or contact customer support.
The cable is typically 50 feet, which works for most residential pools. You should not extend it, as that can cause voltage drop and performance issues. If you have a longer pool, consider a model with a longer cable or a different placement of the power supply.
No, the Nautilus CC Plus is a portable robot, so there’s no permanent installation. You simply connect it when you need to clean and store it when done. This is one of the easiest setups among pool cleaners. If you’re comparing options, you can check out our best pool vacuums guide for more insights.
Yes, the Nautilus CC Plus is designed to work in saltwater pools, but it’s a good idea to rinse the robot with fresh water after each use to prevent corrosion.
Setting up your Dolphin Nautilus CC Plus is straightforward. Follow these steps, and you’ll have a clean pool in no time. For more options, see our buying guide on the best pool vacuums.
We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.
Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.