Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.
The short answer: To clean and maintain the DEWALT DCN680B, you should regularly blow out dust and debris with compressed air, wipe down the exterior, lubricate the magazine and driver guide with a non-petroleum based oil, and check the battery and motor brushes periodically. Always ensure the battery is removed before any cleaning or maintenance. This simple routine will keep your nailer reliable for years.
The DEWALT DCN680B is a cordless 18-gauge brad nailer that runs on a 20V MAX battery. Unlike pneumatic nailers, it has an internal motor and gearbox that can accumulate dust and debris from job sites. Over time, this buildup can cause the nailer to jam, misfire, or slow down. Regular cleaning not only prevents these issues but also extends the life of the tool. Plus, a well-maintained nailer ensures consistent depth and reduces the risk of damaging your workpieces.
These items are affordable and likely already in your workshop. Avoid using petroleum-based lubricants as they can damage the rubber o-rings and seals inside the tool.
Step 1: Prepare the Nailer
Remove the battery and ensure there are no nails left in the magazine. Press the trigger to release any residual pressure.
Step 2: Blow Out Debris
Using compressed air, blow through the magazine, around the driver guide, and into the air vents. This removes sawdust, wood chips, and other debris that can cause jams. Do this in a well-ventilated area or outside.
Step 3: Wipe Down the Exterior
Take a soft, dry cloth and wipe the body of the nailer to remove any surface grime. For stubborn dirt, you can slightly dampen the cloth with water or a mild cleaner, but avoid getting moisture into any openings.
Step 4: Clean the Magazine and Driver Guide
Use the small brush to gently dislodge any stuck debris from the magazine and the driver guide area. Then blow it out again with compressed air. Inspect the driver blade (the part that pushes the nail) for any burrs or damage. If you see nicks, you may need to sand them lightly or replace the driver, but that’s rare if you use good quality nails.
Step 5: Lubricate Moving Parts
Apply a few drops of non-petroleum oil to the driver guide and the magazine. Do not over-lubricate; a drop or two is enough. Then cycle the tool manually (with the battery still out) by pressing the nose down and pulling the trigger a few times to distribute the oil. Wipe off any excess.
Step 6: Check the Battery and Motor
Inspect the battery contacts for dirt or corrosion; clean with a dry cloth if needed. While you’re at it, check the motor brushes if you’re comfortable. If you notice excessive sparking through the vents, it may be time to replace the brushes. But for most users, just keeping the exterior clean and the vents clear is sufficient.
Regular schedule: Clean the nailer after every heavy use or at least once a month for occasional use. If you work in dusty conditions, clean more often.
Jam clearing: If a nail jams, never force it. Remove the battery, open the jam release (consult your manual), and gently pull out the bent nail. Then clear the magazine and inspect for debris before reloading.
Storage: Store the nailer in a dry place, ideally in a case. Keep the battery charged but not fully depleted for long periods. Avoid extreme temperatures.
Common issues: If the nailer skips or has shallow drives, check the depth adjustment wheel and the battery charge. If it’s not firing, ensure the safety tip is fully depressed. If problems persist, refer to the DEWALT manual or contact customer support.
If after cleaning and oiling your nailer still jams frequently, misfires, or has weak driving power, it might need professional service. Contact DEWALT’s authorized service center. Also, if you notice broken or worn parts like the o-rings, it’s best to have them replaced by a pro to avoid further damage. Regular cleaning will minimize these occurrences, but it’s good to know when to stop DIY maintenance.
The DCN680B is designed for 18-gauge brad nails, which are available in various lengths and head types. Using the correct nails is crucial for reliable operation and clean results. The tool accepts brads from 5/8 inch to 2-1/8 inches in length. For most trim and molding tasks, 1-1/4 inch to 2 inch brads work well. Always match the nail length to the thickness of your material to avoid over-penetration or insufficient holding power. Brad nails come with different head styles: the standard small head is less visible, while a larger head provides more holding power but may require filling. Choose based on your project’s aesthetic and structural needs. Avoid using rusty or bent nails, as they can damage the driver blade and cause jams. Stick with reputable brands that meet the 18-gauge specification to ensure smooth feeding and consistent performance.
Even with good intentions, some maintenance habits can do more harm than good. Here are mistakes to steer clear of:
By avoiding these pitfalls, you’ll extend the life of your nailer and reduce downtime.
While the DCN680B is a solid choice for many, it’s not the only option. If you’re shopping for a cordless brad nailer, consider these factors:
Ultimately, the best nailer depends on your specific needs and existing tool collection.
Q: Can I use WD-40 to lubricate my DCN680B?
No, WD-40 is a solvent and not a proper lubricant. It can degrade the internal seals. Use a non-petroleum based oil specifically designed for air tools or nailers.
Q: How often should I clean my nail gun?
For a DIYer, cleaning after every few hundred nails or once a month is fine. For professionals using it daily, a quick blow-out every day or two is recommended.
Q: The nail gun is not driving nails all the way in. What could be wrong?
This usually means the battery is low, the depth adjustment needs to be set deeper, or there is debris blocking the driver. Try adjusting the depth wheel, charge the battery, and clean the tool. If it still fails, check for worn parts.
For more on choosing the right nailer for your projects, check out our best nail guns guide.
We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.
Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.