Disclosure: As an Amazon Associate we earn from qualifying purchases. We may earn a commission if you buy through our links, at no extra cost to you.
The short answer: To keep your monitor arm moving smoothly, regularly dust it, clean the gas springs, tighten loose bolts, and lubricate moving parts with a dry PTFE spray or silicone grease. Avoid oil-based lubricants that attract dust. Wipe down with a microfiber cloth and mild cleaner, and check for wear every few months. Proper maintenance prevents stiffness, sagging, and extends the arm’s life.
We keep a separate, regularly reviewed guide to the best monitor arms if you want product recommendations.
Monitor arms rely on gas springs, friction hinges, and tension adjustments to hold your screen in place. Over time, dust and grime build up on these components, causing friction and resistance. Gas springs can lose pressure, and bolts can loosen from regular movement. If you notice your monitor arm drooping, feeling gritty, or not staying in position, it’s likely due to lack of maintenance or natural wear. The good news: most issues can be resolved with simple cleaning and adjustments.
1. Remove the monitor (optional but recommended): For deep cleaning, detach the monitor from the VESA plate. Set it aside safely. This gives you access to the arm’s joints and springs.
2. Dust off all surfaces: Use a soft, dry microfiber cloth to wipe down the arm’s arms, base, and joints. For crevices, use a can of compressed air or a soft brush to dislodge dust. Pay special attention to the pivot points and gas spring cylinders.
3. Clean stubborn grime: Dampen a microfiber cloth with a mild all-purpose cleaner or isopropyl alcohol (70% or less) and gently wipe the arm’s exterior. Avoid getting liquid into the joints or springs. Dry immediately with another cloth.
4. Clean the gas springs: Wipe gas springs with a dry cloth to remove any oily film or dust. If there is corrosion, use a fine abrasive pad (like a Scotch-Brite) very gently to remove it, then wipe clean. Do not use harsh chemicals on the springs.
5. Inspect for damage: Look for cracks, bent parts, or excessive rust. If you find damage, consider replacing the arm or contacting the manufacturer. A compromised arm can be a safety hazard.
After cleaning, you may need to lubricate moving parts to restore smooth motion. Use a dry PTFE spray or silicone-based grease (not oil-based, which attracts dust). Apply a small amount to the pivot points, friction hinges, and any sliding surfaces. Move the arm through its full range of motion a few times to distribute the lubricant. Then wipe off any excess.
Next, check the tension adjustments. Most arms have a hex key or screw to adjust spring tension. If the arm is too loose (arm sags), tighten the tension screw. If it’s too stiff, loosen it slightly. Make small adjustments and test. Remember, the correct tension should hold the monitor in place without drifting, yet allow easy movement.
Also, check all bolts and screws, including the clamp or grommet mount, and tighten them as needed. A loose base can cause wobble and uneven wear.
For average use, a light dusting every two weeks and a deeper clean every three to six months is sufficient. If you work in a dusty environment or adjust your monitor frequently, you may need to clean and lubricate more often. Pay attention to how the arm feels; if you notice increased resistance or squeaking, it’s time for maintenance. Regular care not only keeps it smooth but also prevents premature failure of gas springs and hinges.
Using WD-40 or oil-based lubricants: These attract dust and can gum up over time, making things worse. Stick to dry lubricants.
Over-tightening bolts: This can strip threads or damage the arm. Tighten until snug, then stop.
Ignoring the gas spring: If your arm uses a gas spring, don’t force it beyond its range. If it fails to hold position, it may need replacement. Some manufacturers sell replacement springs.
Using harsh chemicals: Avoid bleach, ammonia, or strong solvents on the arm’s finish. They can damage paint and plastic.
Neglecting the VESA plate: The screws that attach the monitor to the arm can loosen over time. Check them occasionally to prevent your monitor from falling.
Before you worry about maintenance, it helps to confirm that your monitor and arm are actually compatible. Most monitor arms use the VESA mounting standard, but not every monitor has VESA holes. The two common patterns are 75 x 75 mm and 100 x 100 mm, measured by the distance between the four screw holes on the back of the monitor. If your monitor does not have these holes, you may need a VESA adapter plate, which attaches to the monitor’s existing stand screws or to a proprietary mounting system. Adapters are widely available for many popular monitor brands.
Weight capacity is the other critical factor. Monitor arms are rated for a minimum and maximum weight, and the gas spring or friction hinge is tuned to that range. If your monitor is too light, the arm may not stay down and will drift upward. If it is too heavy, the arm will sag and may not hold position even at maximum tension. Always check the arm’s weight range against your monitor’s weight without the stand. You can find the monitor weight in the manufacturer specifications or by weighing it on a kitchen scale.
Screen size also matters, but not in the way many people assume. A monitor arm does not care about the diagonal screen size directly; it cares about weight and the position of the center of gravity. However, larger screens often weigh more and have a wider center of gravity, which puts more leverage on the joints. For very large or ultrawide monitors, look for arms with a higher weight capacity and a longer reach. The arm’s reach, or the horizontal distance it can extend from the base, should be enough to position the monitor where you want it without overextending the joints.
Finally, consider the mounting surface. Desk clamps need a flat edge with enough thickness, typically between 10 mm and 85 mm, and a clear area underneath. Grommet mounts require a hole in the desk, usually 10 mm to 60 mm in diameter. If your desk has a thick bevel or a metal frame, check that the clamp will fit. Some arms include both clamp and grommet options, giving you flexibility.
Not all lubricants are safe for monitor arms. The best choice is a dry PTFE (polytetrafluoroethylene) spray, often sold as a dry film lubricant. It goes on wet but dries to a thin, non-sticky film that does not attract dust. Silicone grease is another good option for pivot points and sliding surfaces, as it is stable and long-lasting. Avoid any lubricant that contains oil, petroleum distillates, or graphite, because these leave a residue that collects dust and can become gummy. WD-40, for example, is a water displacer and light oil, not a true lubricant, and it will make the problem worse over time.
For cleaning, stick to mild soap and water or isopropyl alcohol. A few drops of dish soap in a bowl of warm water is enough for most grime. Dampen a microfiber cloth, wring it out well, and wipe the arm. Do not spray cleaner directly onto the arm, because liquid can seep into joints and springs. Isopropyl alcohol is useful for disinfecting and removing sticky residue, but use it sparingly and keep it away from plastic parts that might be sensitive. Always dry the arm with a separate cloth to prevent water spots and corrosion.
Microfiber cloths are ideal because they trap dust rather than pushing it around. For crevices, a soft-bristled brush, such as a clean paintbrush or an old toothbrush, can reach into tight spots. Compressed air is helpful for blowing out dust from gas spring cylinders and hinge gaps, but use it in short bursts and hold the can upright to avoid spraying propellant. A small vacuum with a brush attachment can also work for loose dust.
If you notice rust on the arm, a fine abrasive pad can remove it, but use it gently and only on the affected area. Afterward, wipe away any residue and apply a thin coat of silicone grease to protect the metal. For painted surfaces, avoid abrasive pads altogether, as they will scratch the finish.
Monitor arms are mechanical devices, and even with good care, they eventually wear out. The most common failure point is the gas spring, which loses pressure over time and can no longer hold the monitor’s weight. If you have adjusted the tension to its maximum and the arm still sags, the gas spring is likely the culprit. Some manufacturers sell replacement gas springs, but they are not universal, so you will need to match the exact model. If the spring is not available or the arm is out of warranty, replacing the entire arm is usually the simpler and safer option.
Other signs that it is time to replace the arm include cracks in the metal or plastic, a base that will not tighten, or persistent wobbling that cannot be fixed by tightening bolts. A damaged arm can fail suddenly and drop your monitor, which risks damaging the screen and anything below it. If you see any structural damage, stop using the arm immediately.
If your arm is still functional but you are unhappy with its performance, consider whether an upgrade would help. Newer arms may offer better cable management, smoother gas springs, or a wider range of motion. If you frequently move your monitor between portrait and landscape, look for an arm with a quick-release VESA plate. If you have a heavy or ultrawide monitor, choose an arm with a higher weight capacity and a sturdier base. Upgrading can also be worthwhile if you need more reach or a taller vertical range.
Before buying a new arm, check the warranty on your current one. Many reputable brands offer multi-year warranties, and if your arm is defective, you may get a replacement at no cost. Keep your proof of purchase. If you decide to buy new, focus on the features that matter for your setup: weight capacity, VESA compatibility, mounting options, and the type of height adjustment. A little research upfront will save you from repeating the same problems.
A: Vinegar is a mild acid and safe for most surfaces, but it can be corrosive to some metal finishes if left on. It’s better to use a diluted mild detergent or isopropyl alcohol. If you do use vinegar, dilute it with water (1:1) and wipe it off immediately with a damp cloth.
A: If cleaning and lubrication don’t resolve stiffness, the gas spring may be defective or worn out. Check if the tension adjustment is maxed out. If so, you may need to replace the gas spring or the entire arm. Contact the manufacturer for replacement parts. Also, ensure all pivot bolts are not over-tightened; sometimes backing off a quarter turn can help.
A: That depends on the cost. Simple maintenance is always worth it. But if the arm has major damage or the gas spring is unavailable, buying a new arm might be more economical. Check the warranty first; many arms come with multi-year warranties. If you decide to upgrade, consider the features that matter to you. For a comprehensive comparison, you can check out this guide to the best monitor arms.
By following these steps, your monitor arm will continue to glide smoothly, giving you years of ergonomic comfort. Regular maintenance is quick and easy, ensuring your setup stays in top shape.
We don't accept free units or payment for placement. Our rankings combine verified manufacturer specifications, real owner feedback and availability, compared on one transparent S to C rubric.
Honesty note: We have not hands-on tested every product mentioned on this page. Where we have not personally used a product, any ranking referenced here is based on verified specs, aggregated owner feedback, availability and editorial comparison rather than a hands-on review.